{"product_id":"gb54-2-kv26","title":"UNITED UAV T-MOTOR GB54-2 KV26 Gimbal Motor","description":"\u003ch2\u003eT-MOTOR GB54-2 KV26 Gimbal Motor\u003c\/h2\u003e\u003cp\u003eThe UNITED UAV T-MOTOR GB54-2 KV26 is a brushless gimbal motor for camera-stabilization systems used on multirotors, VTOL aircraft, UAV camera platforms, vehicles and hand-held rigs. The original manufacturer page emphasizes smooth motion, low cogging behavior and reliable positioning rather than propulsion thrust. This rewritten product overview retains those technical points while presenting them in a clearer form for system builders, integrators and repair teams.\u003c\/p\u003e\u003cp\u003eThe motor is supplied for custom gimbal development and equipment upgrades. Its published KV26 winding is intended to work within a 3-6S LiPo range. Selection should be based on the complete stabilized payload, axis geometry, controller settings and required holding torque. A gimbal motor should not be chosen from KV alone: camera mass, center of gravity, arm length, balance quality and controller tuning determine whether the system can move smoothly without overheating or oscillation.\u003c\/p\u003e\u003cp style=\"margin: 0; padding: 0; line-height: 0;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0750\/8112\/2008\/files\/UNITED-UAV-tmotor-gb54-2-description-01.webp?v=1790181496\" alt=\"UNITED UAV T-MOTOR GB54-2 gimbal motor description image 1\" loading=\"lazy\" style=\"width: 1800px; max-width: 100%; height: auto; display: block; margin: 0 auto;\"\u003e\u003c\/p\u003e\u003ch2\u003eDesign Highlights\u003c\/h2\u003e\u003cul\u003e\n\u003cli\u003elow cogging torque for controlled, repeatable movement\u003c\/li\u003e\n\u003cli\u003ea flexible cable arrangement intended to reduce drag during balancing\u003c\/li\u003e\n\u003cli\u003ea servo-style connection for straightforward controller integration\u003c\/li\u003e\n\u003cli\u003ea hollow-shaft layout for practical cable or slip-ring routing\u003c\/li\u003e\n\u003cli\u003esealed bearing and housing details intended to resist dust and sand\u003c\/li\u003e\n\u003cli\u003epremium MT-series bearings for smooth rotational support\u003c\/li\u003e\n\u003c\/ul\u003e\u003cp\u003eThe listed magnetic configuration is 12N14P, with an internal resistance of 15Ω and a published torsion figure of 0.45 Nm. These values provide useful reference points when comparing motors, but final performance depends on the gimbal structure and control system. For a new build, test the motor together with the intended controller, power supply and camera rather than assuming results from another frame or axis.\u003c\/p\u003e\u003ch2\u003eMechanical Integration\u003c\/h2\u003e\u003cp\u003eThe source specification lists motor dimensions of ø60.7*25mm, a 12.7mm hole size, a 35cm cable and a motor weight including cable of 156g. Confirm the mounting pattern, shaft or through-hole clearance, connector orientation and available space before ordering. The camera and frame should be statically balanced around each axis before power is applied; poor balance increases current demand, reduces control authority and can introduce visible vibration into recorded footage.\u003c\/p\u003e\u003cp style=\"margin: 0; padding: 0; line-height: 0;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0750\/8112\/2008\/files\/UNITED-UAV-tmotor-gb54-2-description-02.webp?v=1790181532\" alt=\"UNITED UAV T-MOTOR GB54-2 gimbal motor description image 2\" loading=\"lazy\" style=\"width: 1800px; max-width: 100%; height: auto; display: block; margin: 0 auto;\"\u003e\u003c\/p\u003e\u003cp style=\"margin: 0; padding: 0; line-height: 0;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0750\/8112\/2008\/files\/UNITED-UAV-tmotor-gb54-2-description-03.webp?v=1790181541\" alt=\"UNITED UAV T-MOTOR GB54-2 gimbal motor description image 3\" loading=\"lazy\" style=\"width: 1800px; max-width: 100%; height: auto; display: block; margin: 0 auto;\"\u003e\u003c\/p\u003e\u003ch2\u003eCamera Stabilization and Control\u003c\/h2\u003e\u003cp\u003eThe GB54-2 is intended to provide controlled rotational movement for stabilized imaging rather than high-speed propeller operation. Proper results require a compatible brushless-gimbal controller with suitable current limits, motor pole configuration and tuning controls. Start with conservative power and PID values, verify axis direction, then increase authority gradually while monitoring motor temperature and acoustic noise. If the gimbal buzzes, hunts or becomes hot at rest, stop and correct balance or tuning before extended operation.\u003c\/p\u003e\u003cp\u003eFor aerial photography, surveillance cameras and inspection payloads, route motor and sensor cables so they do not pull an axis away from its neutral position. Flexible loops should allow the full commanded range without rubbing the frame. Where the model uses a hollow-shaft arrangement, cable or slip-ring routing still needs strain relief and adequate bend radius. Secure connectors against vibration and keep conductors clear of rotating joints.\u003c\/p\u003e\u003ch2\u003eEnvironmental and Service Considerations\u003c\/h2\u003e\u003cp\u003eSeveral GB-series source pages describe sealed bearing and housing details intended to reduce exposure to dust and sand. This should not be treated as a complete ingress-protection rating. Keep the assembly dry unless the finished gimbal has its own environmental certification, clean contamination promptly and inspect bearings after operation in dusty conditions. Periodically check for radial play, abnormal noise, damaged leads, loose hardware or uneven resistance through the travel range.\u003c\/p\u003e\u003cp style=\"margin: 0; padding: 0; line-height: 0;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0750\/8112\/2008\/files\/UNITED-UAV-tmotor-gb54-2-description-04.webp?v=1790181551\" alt=\"UNITED UAV T-MOTOR GB54-2 gimbal motor description image 4\" loading=\"lazy\" style=\"width: 1800px; max-width: 100%; height: auto; display: block; margin: 0 auto;\"\u003e\u003c\/p\u003e\u003cp style=\"margin: 0; padding: 0; line-height: 0;\"\u003e\u003cimg src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0750\/8112\/2008\/files\/UNITED-UAV-tmotor-gb54-2-description-05.webp?v=1790181524\" alt=\"UNITED UAV T-MOTOR GB54-2 gimbal motor description image 5\" loading=\"lazy\" style=\"width: 1800px; max-width: 100%; height: auto; display: block; margin: 0 auto;\"\u003e\u003c\/p\u003e\u003ch2\u003eInstallation Checklist\u003c\/h2\u003e\u003cp\u003eInspect the motor and hardware on arrival. Verify that fasteners are the correct length and cannot contact windings or moving parts. Balance the payload mechanically, connect the motor with power removed, and perform the first direction test at low output. Confirm that the axis moves freely through its usable range and that the controller does not command sudden uncontrolled motion. Complete a restrained ground test before flight and recheck temperature after the first tuning sessions.\u003c\/p\u003e\u003ch2\u003ePackage Contents and Ordering Notes\u003c\/h2\u003e\u003cp\u003eThe manufacturer page lists one GB54-2 motor and one hardware pack. This Shopify listing provides CW and CCW selection values for catalog consistency; both variants retain the same published electrical and mechanical specification, price and inventory policy. Product weight is recorded from the manufacturer’s Motor Weight (Incl. Cable) value, while the store package selection follows the approved 0.5kg, 10 × 10 × 10cm shipping rule. Review the Specifications tab before ordering and contact UNITED UAV if you need confirmation for a particular camera, controller or gimbal geometry.\u003c\/p\u003e","brand":"UNITED UAV","offers":[{"title":"CW","offer_id":52534081847512,"sku":"TM-GB54-2-KV26","price":82.39,"currency_code":"USD","in_stock":true},{"title":"CCW","offer_id":52534081880280,"sku":"TM-GB54-2-KV26-CCW","price":82.39,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0750\/8112\/2008\/files\/UNITED-UAV-tmotor-gb54-2-main-01.webp?v=1790181480","url":"https:\/\/store.uniteduav.com\/products\/gb54-2-kv26","provider":"UNITED UAV","version":"1.0","type":"link"}